![]() ![]() I have setup reverse-proxy from another jail so that I can access my nextcloud externally.I have been using nextcloud from almost an year and there is no change to IP as I have reserved the IP in my router.And update failed and don’t remember what it said but it was kind of unable to reach. Now you can enjoy the Nextcloud plugin on FreeNAS with SSL enabled.I have clicked update last week and I’m unable to access my nextcloud anymore. ![]() Test logging in, and get started with personalising your Nextcloud system and adding some users. The default credentials that for Nextcloud are in the home directory of the jail (/root). The logs are usually good about pinpointing these, so read them to see where you might have missed something obvious in the nf file. If not, you’re likely to have an NGINX configuration syntax error. If all goes well you’ll see nginx started in the output of that command. Using a shell in the Nextcloud jail, restart nginx with service nginx restart. Otherwise you’ll neee to use some form of dynamic DNS service.Īt this point you should have everything in place. If you’re lucky enough to have a static IP address then you can point your DNS host record to your static IP. Public_IP:29123 (WAN interface) -> Internal_IP:29123 (Internal router LAN interface) -> Internal_IP:8443 (FreeNAS LAN interface) -> Internal_IP:443 (Nextcloud Jail) This is how my NAT and port forwarding chain looks: I use a double NAT setup, so I NAT traffic from my external router interface, through to another internal router.įrom my internal router, I port forward / NAT from the internal router interface through to my FreeNAS box on port 8443.įrom there, the Nextcloud jail does NAT to take the TCP traffic from 8443 to 443 inside the jail (where NGINX is listening on 443). This is the part that comes down to your own network setup. Rename them as per your chosen hostname to keep things organised, and so that they match your nf file entries. /etc/ssl/nginx/ (certificate chain file).Use SCP to copy them up, renaming them as follows: Upload the SSL certificate files to Nextcloud You’ll get a chain file called fullchain.pem, along with a private key file called privkey.pem. ![]() Lets Encrypt will confirm the DNS TXT record and issue you a certificate. Go to your DNS provider control panel and create it with the code you’re given as the value.Īfter creating the record, finish the certificate request. sudo certbot -d -manual -preferred-challenges dns certonlyįollow the prompts until you receive a code to setup your own TXT record with. Request a certificate for your desired hostname using certbot with dns as the preferred challenge. On a debian based system: sudo apt-get install certbot Install certbot if you don’t already have it installed. It entails creating a TXT/SPF record on the domain you own, with a value set to a code that certbot gives you during the certbot request process. Lets Encrypt it free, but you’ll need to renew your certificate every three months.ĭNS-01 challenge certificate generation for Lets Encrypt is a great way to get SSL certificates without a public web server. To configure the Nextcloud plugin on FreeNAS with SSL you don’t need to break the bank on SSL certificate costs from traditional CAs. Generate a free SSL certificate with Lets Encrypt ![]() Populate it with the contents of the gist below, but replace server_name, ssl_certificate, and ssl_certificate_key with your own hostname. Hence the reason you’ll create a new configuration for your SSL setup here. mv /usr/local/etc/nginx/conf.d/nf /usr/local/etc/nginx/conf.d/ Shell into the Nextcloud jail, and rename the default nginx configuration. I chose NAT for my setup as I prefer using one internal IP address for everything I run on the FreeNAS server. The reason for selecting port 8443 for Nextcloud is because the FreeNAS web UI listens on port 443 for SSL too.Īn alternative could be to use DHCP instead of NAT for the jail. Add another NAT rule to point 8443 to 443 for SSL. Stop the jail once it’s running and edit it. Start off by Installing the Nextcloud Plugin in a jail. Look at some options for setting up home networking for public access.Apply a free SSL certificate using Lets Encrypt and DNS-01 challenge validation.Configure NGINX inside the jail by adding a customised configuration with SSL enabled.Add an extra NAT port for SSL to the jail.Install the Nextcloud plugin in a FreeNAS BSD jail.This is critical, especially for a system exposed to the internet. But, you don’t get SSL enabled by default. The FreeNAS Nextcloud plugin installation works great with automatic configuration thanks to a recent pull request. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |